Why We Use the Wavetek SSI-3000 and Ramsey COM-3 for Wireless System Repair
Why We Use the Wavetek SSI-3000 and Ramsey COM-3 for Wireless System Repair
A wireless microphone that drops out mid-song, an in-ear monitor pack that hisses, a receiver that only works when the singer stands in one spot: these are some of the most frustrating problems in live sound, and they are also the hardest to diagnose. You cannot see radio frequency (RF) energy, and you cannot hear whether a transmitter is 15 kHz off frequency or over-deviating. You have to measure it.
That is why Donald Lee Service keeps two dedicated RF communications service monitors on the wireless bench: the Wavetek SSI-3000 and the Ramsey COM-3. Here is what they do, why we chose them, and what it means for your wireless system.
What Is an RF Service Monitor?
An RF service monitor is an all-in-one radio test instrument. In a single box it combines:
- A precision RF signal generator that produces a clean carrier at an exact frequency and level
- A modulation source so that carrier can carry a known test tone
- A sensitive, calibrated receiver that measures the frequency, power and modulation of a transmitter
- Deviation and modulation meters that show exactly how much a transmitter is modulating
- Frequency counters for RF and audio
In other words, it lets us act as a perfect transmitter when we are testing a receiver, and a perfect receiver when we are testing a transmitter. That is the only way to isolate which half of a wireless system has actually failed.
The Wavetek SSI-3000
The Wavetek SSI-3000 is a full-featured communications analyzer covering roughly 400 kHz to 1 GHz, which spans every band professional wireless systems have ever used: VHF, the UHF television bands where most microphones live (470 to 608 MHz in the United States), the 900 MHz band, and everything in between.
Why we rely on it:
- Frequency accuracy. Modern wireless systems are frequency-agile and sit on tightly spaced channels. The SSI-3000 tells us whether a transmitter is really on the frequency its display claims. A drifted crystal or oscillator shows up immediately.
- Receiver sensitivity testing. We inject a known, calibrated signal level into a receiver and watch where it squelches, where it opens, and how much audio noise rides along. A receiver that needs ten times more signal than specification has a front-end problem, and we can prove it before touching a soldering iron.
- Modulation and deviation measurement. Analog wireless systems use FM with companding. If deviation is low, the mic sounds thin and noisy; if it is high, it distorts and splatters into neighboring channels. The SSI-3000 displays deviation directly so we can set it to factory specification.
- Spectrum and spurious checks. We can sweep across a band to find a transmitter that is producing spurious emissions or a receiver that is being hammered by intermodulation from nearby channels.
The Ramsey COM-3
The Ramsey COM-3 is a compact service monitor covering 100 kHz to 999.999 MHz with 500 Hz tuning resolution and a seven-digit frequency display. It generates both AM and FM, measures FM deviation on a 20-segment bar graph, and includes RF and audio frequency counters.
Why we keep it beside the Wavetek:
- A second opinion. Measurement is only trustworthy when it can be cross-checked. When the SSI-3000 and the COM-3 agree on a transmitter's frequency and deviation, we know the reading is real and not an instrument fault.
- Precise generator levels. The COM-3 produces calibrated output from 0.1 microvolt to 10,000 microvolts in five ranges. That lets us simulate a performer at the back of a 2,000-seat theater and watch exactly how a receiver behaves on the edge of its range.
- Companding and tone measurement. Many systems rely on a pilot tone to open the receiver squelch. The audio counter on the COM-3 confirms the pilot tone is present and at the right frequency, which is one of the most common hidden causes of "my receiver will not unmute."
Why Two Instruments Instead of One?
Any competent shop can own one piece of test gear. We use two for the same reason we test every tube on a Hickok 799 and check every recap on an oscilloscope: repair should be verified, not assumed.
- The two monitors have different front ends and different reference oscillators, so they fail in different ways. If they ever disagree, we know to recalibrate before trusting either.
- We frequently need a transmitter and a receiver on the bench at the same time. One instrument can generate the carrier into a receiver under test while the other listens to the transmitter under test.
- When a customer brings in a full rack of eight or sixteen channels, two instruments cut diagnostic time dramatically.
What This Means for Your Wireless System
Here is how these instruments change the outcome of a typical repair:
Problem: Intermittent dropouts on a Shure, Sennheiser or Audio-Technica handheld. Without test equipment, the usual "fix" is a new antenna or a new battery. With the SSI-3000 we measure the transmitter's actual output power and frequency, then measure the receiver's sensitivity. Nine times out of ten the fault is a weak transmitter final stage, a cracked antenna connection or a detuned receiver front end, and we can show you the numbers.
Problem: In-ear monitor pack hisses or sounds thin. We measure the transmitter's deviation and companding behavior. Low deviation or a failed compander chip shows up as a clear measurement, not a guess.
Problem: System worked for years and suddenly will not lock. Since the 2017 to 2020 FCC repack, parts of the 600 MHz band are illegal to use and are occupied by cell carriers. We sweep the band your system is on and tell you honestly whether it can be realigned or must be replaced. See our article on wireless microphones and FCC frequency rules for the full story.
Alignment to Factory Specification
After every wireless repair, we realign the unit against the manufacturer's service specification using these monitors:
✓ Transmitter frequency set to within manufacturer tolerance ✓ Transmitter power verified at rated output ✓ Deviation and pilot tone set to specification ✓ Receiver sensitivity and squelch confirmed with a calibrated signal ✓ Audio output level and distortion checked end to end
You get the documented measurements with your invoice, so you know the system is right, not just "working today."
Our Commitment to Measurement
The Wavetek SSI-3000 and Ramsey COM-3 are not glamorous. They are heavy, they are older than many of the technicians working in audio today, and they require regular calibration. But they tell the truth about RF, and in wireless audio the truth is the only thing that keeps a performer on the air.
When you bring a wireless system to Donald Lee Service you get:
✓ Real RF measurements instead of guesswork ✓ Cross-checked results from two independent instruments ✓ Alignment to factory specification after every repair ✓ Honest advice on whether a system can be legally and reliably used
Professional Wireless System Service
Bring your wireless microphones, in-ear monitor systems, antenna distribution and receivers to Donald Lee Service for:
✓ Component-level transmitter and receiver repair ✓ Frequency, power and deviation alignment ✓ Receiver sensitivity and squelch testing ✓ Pilot tone and compander diagnosis ✓ Frequency coordination and FCC band compliance checks
$50 Diagnostic/Estimate Fee, waived when you approve the repair
Serving Kissimmee, Orlando, and Central Florida, with mail-in service nationwide
📞 407-978-6690
✉️ Service@DonaldLeeService.com
📍 1014 N. Hoagland Blvd., Kissimmee, FL 34741
🕒 Mon-Fri 9am-3pm